GC8261, GC8260, GC8225, GC8220, GC8210 A B C DE F G 1 H I J K W L M V U T SR Q P N X O EnGlish 6 indonEsia 18 30 Bahasa MElayu 54 64 GC8261, GC8260, GC8225, GC8220, GC8210 6 EnGlish introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips. com/welcome. The powerful pressurised ironing system produces non-stop steam to make ironing easier. Thanks to the large water tank, you can iron without interruption. When the water tank is empty, you can detach it and refill it immediately. We hope you enjoy using this ironing system. General description (Fig. 1) a B C d E F G h i J K l M n o P Q R s T u V W X Supply hose Handle (GC8261/GC8260 only: with soft grip) Temperature dial Steam trigger Temperature light Steam lock Shot-of-steam button (GC8261/GC8260/GC8225/GC8220 only) Soleplate Safe storage lock (GC8261/GC8260 only) Iron stand Detachable water tank Cord & hose storage hook Calc-Clean rinsing cap Filling opening Water tank release lever Steam generator On/off button with power-on light (GC8261/GC8260/GC8225/ GC8220 only) Transport handgrip Water tank refill light (GC8261/GC8260/GC8225/GC8220 only) Calc-Clean light (GC8261/GC8260 only) Mains cord Steam buttons (+/-) (GC8261/GC8260/GC8225/GC8220 only) Steam generator control panel with steam light (GC8261/GC8260/ GC8225/GC8220 only) p = maximum steam [ = moderate steam ] = minimum steam a = no steam On/off switch with power-on light (GC8210 only) important Read this user manual carefully before you use the appliance and save it for future reference. danger - Never immerse the iron or the steam generator in water. Warning - Check if the voltage indicated on the type plate corresponds to the local mains voltage before you connect the appliance. EnGlish - - - Do not use the appliance if the plug, the mains cord, the supply hose or the appliance itself shows visible damage, or if the appliance has been dropped or leaks. If the mains cord or the supply hose is damaged, you must have it replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard. Never leave the appliance unattended when it is connected to the mains. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Do not let the mains cord and supply hose come into contact with the hot soleplate of the iron. If steam escapes from under the Calc-Clean rinsing cap when the appliance heats up, switch off the appliance and tighten the Calc-Clean rinsing cap. If steam continues to escape when the appliance heats up, switch off the appliance and contact a service centre authorised by Philips. Never remove the Calc-Clean rinsing cap when the steam generator is hot. Do not use any other cap on the steam generator than the Calc-Clean rinsing cap that has been supplied with the appliance, as this cap also functions as a safety valve. Caution - Only connect the appliance to an earthed wall socket. - Check the mains cord and the supply hose regularly for possible damage. - Always place and use the iron and the steam generator on a stable, level and horizontal surface. - The soleplate of the iron can become extremely hot and may cause burns if touched. - When you have finished ironing, when you clean the appliance, when you fill or empty the water tank and also when you leave the appliance even for a short while: put the iron on the iron stand, switch off the appliance and remove the mains plug from the wall socket. - Rinse the steam generator regularly according to the instructions in chapter `Cleaning and maintenance'. - This appliance is intended for household use only. Electromagnetic fields (EMF) This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. 8 EnGlish Before first use Note:The iron may give off some smoke when you use it for the first time.This is normal and stops after a short while. Note: Some particles may come out of the soleplate when you use the iron for the first time.This is normal; the particles are harmless and stop coming out of the iron after a short while. Note:When you switch on the appliance, the steam generator may produce a pumping sound. This is normal; the sound tells you that water is pumped into the steam generator. 1 Remove any sticker or protective foil from the soleplate and clean the soleplate with a soft cloth. Preparing for use 1 Place the steam generator on a stable and level surface, e.g. on the hard part of the ironing board or on a table. Filling the detachable water tank You can fill the water tank at any time during use. Do not put hot water, perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank. Do not overfill the water tank, otherwise water may spill out of the filling opening when you reinsert the water tank. 1 Remove the detachable water tank from the steam generator. Fill the water tank with tap water up to the MAX indication. Note: If the tap water in your area is very hard, we advise you to mix it with an equal amount of distilled water. Slide the water tank firmly back into the steam generator (`click'). Note: If the water tank is not properly placed, the iron does not produce any steam. Water tank refill light (GC8261/GC8260/GC8225/GC8220 only) When the water tank is empty, the water tank refill light starts flashing and steam ironing is no longer possible. 1 Remove the water tank and fill it. Put the water tank back into the steam generator. , The iron is ready for steam ironing again. EnGlish setting the temperature 1 Check the laundry care label of the article to be ironed to determine the required ironing temperature. - 1 for synthetic fabrics ( e.g. acrylic, viscose, polyamide) and silk - 2 for wool - 3 for cotton - MAX for linen To set the required ironing temperature, turn the temperature dial to the appropriate position. Put the mains plug in an earthed wall socket. Switch on the appliance. GC8261/GC8260/GC8225/GC8220 only: Press the on/off button once. , The power-on light of the on/off button goes on. , The temperature light on the iron goes on. When the iron has reached the set temperature, the temperature light goes out. - On On Note: During ironing, the temperature light goes on from time to time.This indicates that the iron is heating up to the set temperature. , The steam light starts flashing. After approx. 2 minutes, the steam light stays on continuously to indicate that the steam generator is ready for steam ironing. - GC8210 only: Set the on/off switch to `on'. , The power-on light in the on/off switch goes on. , The temperature light on the iron goes on. When the iron has reached the set temperature, the temperature light goes out. Note: During ironing, the temperature light goes on from time to time.This indicates that the iron is heating up to the set temperature. , After approx. 2 minutes, the steam generator is ready for steam ironing. Tips - If you do not know what kind or kinds of fabric an article is made of, determine the right ironing temperature by ironing a part that is not visible when you wear or use the article. - If the fabric consists of various kinds of fibres, always select the temperature required by the most delicate fibre, i.e. the lowest temperature. For example: if a fabric consists of 60% polyester and 40% cotton, it must be ironed at the temperature indicated for polyester ( 1) and without steam. - Start ironing the articles that require the lowest ironing temperature, i.e. those made of synthetic materials. - If you set a lower temperature during ironing, wait until the iron has cooled down to the set temperature before you continue ironing. To make the iron cool down faster, simply press the steam trigger or iron a piece of cloth. 10 EnGlish using the appliance steam ironing The supply hose may become hot during a long ironing session. Note:The system may occasionally produce a pumping sound during steam ironing.This is normal and tells you that water is pumped into the steam generator. 1 Make sure there is enough water in the water tank. Make sure the appliance is plugged in and switched on (see chapter `Preparing for use'). Set the required ironing temperature (see chapter `Preparing for use'). Steam ironing is only possible at ironing temperatures higher than 2. GC861/GC860/GC85/GC80 only: Set the required steam setting with the + and - buttons on the steam generator control panel. p for maximum steam (temperature setting MAX). [ for moderate steam (temperature settings 3 to MAX). ] for minimum steam (temperature settings 2 to MAX). a for no steam (temperature settings 1 to MAX). , The steam light flashes to indicate that the steam generator is heating up. , After approx. 2 minutes, the steam light stays on continuously to indicate that the steam generator is ready for steam ironing. Note: During ironing, you can adjust the steam setting with the + and - steam buttons. It takes a few moments before the amount of steam is adjusted. 5 Press the steam trigger to start steam ironing. When you put down the iron during ironing, put it on its heel or on the iron stand. , The opening and closing of the steam valve in the steam generator causes a clicking sound. This is normal. steam lock function The steam lock allows you to steam iron non-stop without having to press the steam activator continuously. - When you slide the steam lock forwards, the iron produces steam continuously. To stop steaming, slide the steam lock backwards. - When the steam lock is deactivated, the iron only produces steam when you press the steam trigger. Note: Release the steam lock when you put the iron on its heel or on the iron stand.This prevents that hot steam escapes from the iron or that the iron stand gets wet. Vertical steaming Never direct the steam at people. EnGlish 1 Hold the iron in vertical position and press the steam trigger to steam iron hanging curtains and clothes (jackets, suits, coats). 11 Shot of steam (GC8261/GC8260/GC8225/GC8220 only) A powerful shot of steam helps to remove stubborn creases. 1 Set the temperature dial to a position between 3 and MAX. Press the shot-of-steam button. Note: Use the shot-of-steam function intermittently. If water droplets come out of the soleplate, let the iron heat up for at least one minute before you use the shot-of-steam function again. ironing without steam There are one or two ways to iron without steam: - All types: Simply start ironing without pressing the steam trigger. - GC8261/GC8260/GC8225/GC8220 only: Select steam setting a (no steam) and start ironing. Tips When you steam iron woollen fabrics, shiny patches may occur. To prevent this, use a dry pressing cloth or turn the article inside out and iron the reverse side. Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent shiny patches. Iron velvet and other fabrics that tend to acquire shiny patches in one direction only (along with the nap) while you apply very little pressure. Do not use steam when you iron coloured silk. This could cause stains. 1 EnGlish Cleaning and maintenance after ironing 1 Put the iron on the iron stand (see chapter `Storage') and switch off the appliance. Remove the mains plug from the wall socket and let the appliance cool down. Wipe scale and any other deposits off the soleplate with a damp cloth and a non-abrasive (liquid) cleaner. Clean the upper part of the iron and the outside of the steam generator with a moist cloth. 5 Empty the water tank after cleaning. Calc-Clean function Never remove the Calc-Clean rinsing cap when the steam generator is hot. VERY IMPORTANT: Rinse the steam generator once a month or after every 10 times of use, to prevent damage to the appliance and for optimal steaming performance. 1 Unplug the appliance and let it cool down for hours. Remove the detachable water tank. Hold the steam generator with both hands and shake well. Off Turn the steam generator on its side with the Calc-Clean rinsing cap facing upwards, and remove the Calc-Clean rinsing cap. EnGlish 5 Empty the steam generator into the sink. 1 6 Fill the steam generator with fresh water and shake again. Empty the steam generator into the sink again. 8 Repeat steps 6 & twice to obtain the best result. Screw the Calc-Clean rinsing cap tightly back onto the steam generator. Calc-Clean light (GC8261/GC8260 only) 1 The Calc-Clean light flashes for 30 seconds ...